A golf rangefinder shows a distance in the eyepiece, but that number is only useful if it is in the same unit you think in and the same unit the course is marked in. One yard is 0.9144 meters, so a reading of 150 is a different shot depending on whether the display is set to yards or meters. This article explains how to switch units on a ZYDAR Z1 or a ZYDAR Pro Z1, and when that setting matters. It is based on the live zydar.com product pages and the official English user manuals on zydar.com, fetched November 16, 2026, plus factory-confirmed Pro Z1 range and field-of-view figures received the same day. It is a how-to guide, not a ranking of every model on the market.
Yards or meters: how to tell which unit is selected
Both official manuals list “Unit of Measurement (Meter / Yard)” as a display indicator. The live Z1 and Pro Z1 product pages also state that both models support two units: yards and meters. When the unit is on, look in the display for Y (yards) or M (meters) next to the distance. If the number does not match a sprinkler head, a scorecard, or a GPS watch, check this indicator before you assume the rangefinder is wrong.
How to switch between yards and meters
The official Z1 and Pro Z1 manuals give the same unit-conversion steps, under “Unit Conversion & OLED Brightness Adjustment”:
- Press the Power button to turn the rangefinder on.
- Hold the Mode button for 3 seconds to enter Settings mode.
- Use the Power button to select “Y” or “M,” then press the Mode button to confirm.
- Use the Power button to select an OLED brightness level from 1 to 4, then press the Mode button to confirm and exit Settings.
On the Pro Z1, the official manual notes that OLED brightness adjustment must be done in OLED display mode. The Pro Z1 can switch between its black LCD display and its red OLED display by double-tapping the Mode button. The unit-selection steps themselves (hold Mode for 3 seconds, choose Y or M, confirm with Mode) are the same on both models.
The manuals do not state a factory default unit, and they do not say whether the last Y/M choice is stored after the unit powers off. If you are not sure, look at the Y or M indicator after you turn the rangefinder on, and repeat the steps above if needed.
When the unit setting matters
In the United States, course markers, sprinkler heads, and scorecards are commonly in yards. In many other countries those same markings are in meters. The mismatch that causes trouble is mixing the two: a laser in meters against a scorecard in yards, or club distances you memorized in yards against a display that is set to M.
A 150-yard shot and a 150-meter shot are not the same club. Because 1 yard equals 0.9144 meters:
- 100 yards = 91.44 meters
- 150 yards = 137.16 meters
- 200 yards = 182.88 meters
- 100 meters ≈ 109.4 yards
- 150 meters ≈ 164.0 yards
If a rangefinder set to meters reads 150, that is about 164 yards, or roughly one club longer than a 150-yard shot. If it is set to yards and you treat the number as meters, you will be short. Before a round, and especially when you play a course marked in a different unit than you usually use, confirm that the display, the course markings, and your own club distances are all in the same unit. The same check applies when you compare a laser reading with a GPS watch or a yardage book. For a simple practice loop that depends on a consistent number, see How to Practice Distance Control at the Range with a Rangefinder.
Range figures in both units
Switching Y and M changes the unit of the distance in the display. It does not change the laser’s maximum or minimum range. Factory confirmation for the Pro Z1, which now also appears on the live Pro Z1 product page, is an overall range of 5–1,300 yards (4.6–1,188 meters). The live Z1 product page lists the same overall range. Both live product pages list a flag range of up to 300 yards; both official manuals list that flag range as 300 yards / 274 meters. Both product pages and both manuals list ranging accuracy as +/- 1 yard (a manufacturer specification).
Both official manuals also say, in troubleshooting, that the units cannot measure below 5 yards or over 1,300 yards. The 4.6-meter lower figure is the metric equivalent of that 5-yard minimum, as confirmed by the factory for the Pro Z1.
Some specifications on a product page are also written in more than one unit. The factory-confirmed field of view for the Pro Z1 is 122 yards (367 feet) at 1,000 yards. That figure describes the width of the view at a set distance; it is not the Y/M setting for a ranging readout. It is still a reminder to read the unit on a spec sheet, not only the number.
Slope, pin mode, and the unit setting
The unit setting is separate from slope and from pin mode. When slope is on, the official manuals say the display can show both straight-line distance and slope-compensated distance, plus slope in degrees. Those distances use the selected yard or meter unit; the slope angle is shown in degrees. Pin mode, which locks onto the nearest object and confirms a flag reading with vibration and a flag icon, also reports its distance in the selected unit. Switching Y or M does not turn slope on or off, and it does not enter or exit pin mode. For those features, see How to Use a Slope Rangefinder (and When to Turn Slope Off) and What Is Pin Mode on a Golf Rangefinder?.
Z1 and Pro Z1
The unit-conversion steps in the official manuals are the same for the Z1 and the Pro Z1, and both live product pages list yards and meters. The published difference between the two models that is relevant here is the display: a red OLED on the Z1, and a dual-color display (black LCD and red OLED) on the Pro Z1, which you switch by double-tapping Mode. For a side-by-side of the two models, see ZYDAR Z1 vs Pro Z1: Which Golf Rangefinder Should You Buy?.
FAQs
How do I switch a ZYDAR rangefinder from yards to meters?
The official Z1 and Pro Z1 manuals say to hold the Mode button for 3 seconds to enter Settings, use the Power button to select “Y” or “M,” and press Mode to confirm. You then set OLED brightness (levels 1 to 4) with the Power button and press Mode again to confirm and exit.
How can I tell whether my rangefinder is in yards or meters?
Look at the unit indicator in the display. Both official manuals list “Unit of Measurement (Meter / Yard)” as a display indicator, and Settings uses “Y” for yards and “M” for meters. If a reading disagrees with a scorecard or a GPS watch, check this indicator first.
Why does the unit setting matter on the course?
One yard equals 0.9144 meters, so a “150” reading is a different shot in yards than in meters. Match the rangefinder’s unit to the course markings and to the unit you use for club distances. Mixing yards and meters is a common way to take the wrong club, even when the laser reading itself is correct.
What is the Pro Z1 range in yards and in meters?
The factory-confirmed overall range for the Pro Z1 is 5–1,300 yards (4.6–1,188 meters). The live product page lists a flag range of up to 300 yards, and the official manual lists that flag range as 300 yards / 274 meters. Ranging accuracy is listed as +/- 1 yard (manufacturer specification).
Does switching units change slope or pin mode?
No. The official manuals treat unit conversion, slope on/off, and pin mode as separate controls. Changing Y or M changes the unit of the displayed distance. It does not move the external slope switch or enter pin mode, which is activated by holding the Power / Measurement button.
Related reading
- How to Practice Distance Control at the Range with a Rangefinder
- How to Choose a Golf Rangefinder: 7 Specs That Actually Matter
- What Is Pin Mode on a Golf Rangefinder? Flag Lock and Vibration Explained
- How to Use a Slope Rangefinder (and When to Turn Slope Off)
- How to Shoot a Rangefinder as an Absolute Beginner?
- Why Is My Golf Rangefinder Not Accurate?
- Golf Rangefinder vs GPS Watch for Beginners
- ZYDAR Z1 vs Pro Z1: Which Golf Rangefinder Should You Buy?